🌸 DIY Garden Arbor... Designing & Building TutorialIf your arbor will shelter your front gate, try repeating some of the architectural elements of your house in the arbor's design. Check out these step-by-step instructions: |
↓ DIY Arbor Plans:
▸ Arbor ▸ Garden Arbor ▸ Garden Arbor Getaway ▸ Trellised Arbor ▸ Victorian Arbor |
 ❈ Starting ThoughtsFew projects are as easy to build or as beautiful to look at as an arbor. An arbor can grace a garden pathway, hide a neighbor's home or house your front gate. It's no wonder that people have been raising them for thousands of years. We suggest building your arbor from pressure-treated lumber or rough-cut redwood. It's cheaper than dressed lumber and, left unpainted and covered with wisteria, it's sure to age handsomely. |
| In fact, all kinds of climbing flowers love arbors: bougainvillea, clematis, honeysuckle, trumpet vine, wisteria and, of course, climbing roses. If you like variety, consider the climbing annuals: sweet pea, morning glory, nasturtium. You'll replant them each spring, but that's half the fun. |
 ❈ ConstructionDon't overbuild your arbor - whatever you plant to climb the arbor will support itself to a large degree. Four-by-4s or 6-by-6s will be more than adequate for arbor posts. By and large, build horizontal crossbeams out of 2 x 6's or 2 x 8's. And the top level of crosspieces is typically fashioned from 2 x 3's. Keep it light: an arbor should leap upward like a tree, with a canopy that's proportional to its posts. If you use pressure-treated lumber, you can just sink the posts into the ground, provided there's decent drainage in that area. |
| Yes, we know about pier blocks and post anchors, but we've sunk redwood and pressure-treated southern pine posts 30 years ago that are still standing. For an 8-foot-high post, dig the posthole 1 foot across and at least 2' deep. Order enough 3/8" gravel to fill the bottom of each hole 6" deep.
For plumbing posts (that is, making them perfectly vertical), nothing beats foundation stakes, the perforated steel rods ordinarily used to bolster concrete foundation footings. First, plumb the post with a carpenter's level. |
| Then, using one face of the post as a guide, drive a foundation stake diagonally into the soft dirt around the hole. Hammer a double-headed nail through the stake into the post. Check plumb again and drive a second foundation stake in at a right angle to the first, and nail it to the post. Check for plumb one last time and fill the hole with concrete. Let the posts set for a day or two. When the concrete is dry, pull out the foundation stakes and top the hole with gravel for good drainage.
The rest is straightforward. It's easiest to cut all beam and crosspiece ends now, before you attach them to the posts. While you're still on solid ground, also drill the holes for any nails, screws or bolts you'll use to attach the wooden members. |
 That done, you're ready to attach the beams and crosspieces. You'll need a sturdy stepladder, a carpenter's level, a tape measure, and - depending on whether you nail or lag-bolt elements together - a hammer or a drill, a 3/8" spade bit and a socket wrench. A helper will make the job easier, too.
Start by tacking (temporarily attaching) one end of a beam to a post. Use your carpenter's level to level it, then tack the second end. If you're putting up a pair of beams, level the second to the first. When you're happy with their positions, nail or screw them all the way. As you'll note in the illustration, we prefer to use 3/8" lag bolts with washers. |
| Once the beams are secured, the rest is a cakewalk: Use your tape measure to space the crosspieces, then nail or screw the crosspieces atop the beams in their predrilled holes. We used 10d box nails because their shanks are skinnier than common nails. |
❈ A Design Portfolio  Arbors are remarkably adaptable. You can cut designs into the ends of the arbor beams or arch the beams to dramatically change the overall look of the structure.
By varying the spacing of the crosspieces, you can make your arbor feel open and airy or snug and cozy. If your arbor will shelter your front gate, try repeating some of the architectural elements of your house in the arbor's design. That way, you can tie it aesthetically to the house. |
| Or you can dress up your arbor by painting it the same color as your window trim. Anything goes. Because design elements often repeat themselves, cut out all beams and crosspieces at the same time, so attaching them to the post goes quickly. |
 A jigsaw works fine for the task, but a band saw is even better if you have one - or have access to one. First, make a template of heavy paper or cardboard. Trace the uncut beam end on the paper, then sketch different profiles on the tracing. Cut out the one you like best and use it to trace the profile on the wood. Cut the end, and then use that piece as a pattern for the remaining cuts.
Lastly, notched arbor pieces can be handsome and are generally stronger. But they're also much more complicated. The beauty of the construction sequence above is its simplicity: you can level crosspieces in place after the posts are erected. If a post is too long, just trim it off. Notched post-beam construction, on the other hand, requires setting posts to an exact depth or notching a post in place while perched atop a stepladder. |
As a participant in the WOOD Store Affiliate Program, we earn commissions on sales generated by advertising and linking to WOODStore.net.
This garden arbor is made of high-quality fir wood which is solid and long-lasting. Every part are closely connected with good-quality metal hardware, which makes whole frame stand steadily.
Use at walkways, gateways, garden entrance, poolside and pathway etc to meet your needs for ornament or decoration.
High-quality hardware and detailed installation instruction are included. Specific graphic installing steps are listed for your reference.
📌 We are a participant in the Amazon.com Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.